Center of Electrical Machines Testing and Monitoring (CEMTM) holds training courses related to testing and monitoring of electrical machines. Courses will be held in Iran university of science and technology. Moreover it can be held at client’s site on request.
| 1 | Tap changers: the basis of operation, service, maintenance and repair of power and distribution transformers | 16 Hours – Practical |
| 2 | Service, maintenance and repair of power and distribution transformers | 24 Hours – Practical |
| 3 | Transformer electrical tests | 16 Hours – Practical |
| 4 | Transformer oil tests | 24 Hours – Practical |
| 5 | Comprehensive course on power transformers | 40 Hours – Practical |
| 6 | Motor current signature analysis (MCSA) | 24 Hours – Practical |
| 7 | Analysis of Rotary Machines Based on Offline Tests | 16 Hours – Practical |
| 8 | Troubleshooting DC motors using Online motor current signature analysis (MCSA) | 16 Hours – Practical |
| 9 | Analysis of partial discharge in rotary machines | 16 Hours – Practical |
| 10 | Vibration analysis, Level 1 | 24 Hours – Practical |
| 11 | Vibration analysis, Level 2 | 24 Hours – Practical |
| 12 | Troubleshooting turbo machines by analyzing the orbit diagram and approximate center position of the shaft | 16 Hours – Practical |
| 13 | Introduction to Hydrodynamic Bearings and their Troubleshooting | 16 Hours – Practical |
| 14 | Identification and Troubleshooting Induction-Mechanical Electric motors | 16 Hours – Practical |
| 15 | Rotating machine balancing | 16 Hours – Practical |
| 16 | Preventive maintenance in electric motors | 16 Hours – Practical |
| 17 | Industrial oil and lubrication of rotary machines | 16 Hours – Practical |
| 18 | Basic Acoustic Principles and it’s Application in Rotating Equipment Troubleshooting | 16 Hours – Practical |
| 19 | Linear and nonlinear modal analysis | 16 Hours – Practical |
| 20 | Repair, maintenance, and troubleshooting tests for low and medium voltage generators | 24 Hours – Practical |
| 21 | Protection of low-voltage generators and turbo generators | 16 Hours – Practical |
| 22 | Shaft voltage and leakage current in rotating machine bearings | 16 Hours – Practical |
| 23 |
Checking the protection of synchronous generators with DigSILENT
|
16 Hours – Software |
| 24 |
Protective coordination of power plant and grid with DigSILENT
|
16 Hours – Software |
| 25 | Simulation and analysis of synchronous generator behavior with AVR, Governor and PSS using DigSILENT | 16 Hours – Software |
| 26 | Overhaul Turbo Gas and Steam Power Generators | 16 Hours – Practical |
| 27 | Partial discharge in generators | 16 Hours – Practical |
| 28 | Protection and control in gas and steam generators | 16 Hours – Practical |
| 29 | Principles of design, testing and commissioning of high voltage cables | 16 Hours – Practical |
| 30 | Maintain High and Medium voltage Cables, Cable head and Joints according to CIGRE Guidelines | 8 Hours – Practical |
| 31 | Principles of Installation and Maintenance of medium and high voltage Cable, Cable head and Joints Based on CIGRE Guidelines | 16 Hours – Practical |
| 32 | Partial Discharge Testing of Medium and High voltage Cables Offline and Online | 8 Hours – Practical |
| 33 | Determination of permanent and essential heat capacity of high voltage cables | 8 Hours – Practical |
| 34 | Thermography level 1 | 24 Hours – Practical |
| 35 | Thermography level 2 | 16 Hours – Practical |
| 36 | Preventive maintenance of electrical equipment | 24 Hours – Practical |
| 37 | A review of the applications of active thermography in inspection | 8 Hours – Practical |
| 38 | Applications of thermography in troubleshooting electrical equipment | 8 Hours – Practical |
| 39 | Applications of thermography in troubleshooting mechanical equipment | 8 Hours – Practical |
| 40 | Maintenance of diesel generators | 24 Hours – Practical |
| 41 | Protection systems and types of relays | 16 Hours – Practical |
| 42 | Earthing system |
16 Hours – Practical |
| 43 | Industrial valves control | 32 Hours – Practical |
| 44 | Automatic actuator LBV, ESD, GAS / Hydraulic | 24 Hours – Practical |
| 45 | GIS posts and equipment | 24 Hours – Practical |
| 46 | Servicing and maintenance of distribution, over-distribution and transmission substations
|
24 Hours – Practical |
| 47 | Testing and commissioning of distribution and transmission substations | 24 Hours – Practical |
| 48 | Protective earth connection and industrial electrical earth connection | 16 Hours – Practical |
⇐ Click here to download the full list of courses.
For more information, please contact us
- Participants in the courses will receive a valid certificate from Cemtm.
- Courses will be held in Iran university of science and technology. also if you want, it can be held at your site on request.
